Blog

Electrical Corona vs Infrared: What Each Method Shows

Two of the most common tools in electrical inspection look at the same equipment and see almost opposite things. Infrared thermography reads heat. Corona UV inspection reads a faint discharge of light. A problem that is glaring to one can be invisible to the other, which is exactly why experienced inspectors treat them as partners rather than substitutes.

Published

A quick note on the word first. Electrical corona is partial discharge in the air around high-voltage equipment, a small ionization that gives off ultraviolet light. It has nothing to do with the virus. Everything below is about the electrical phenomenon.

What infrared thermography shows

Infrared cameras measure heat. On electrical gear, excess heat usually means excess resistance, and excess resistance usually means something is wearing out: a loose connection, a corroded contact, an overloaded conductor, an unbalanced phase.

Thermography is strong when a fault converts energy into heat. A high-resistance joint carrying current warms up, and that warm spot stands out against cooler neighbors. The method shines on current-carrying connections and loaded components, and it gives you a measurable quantity, temperature, that you can compare point to point.

Its blind spot is the problem that does not get hot. Some insulation and high-voltage defects leak energy as discharge rather than heat, and a thermal camera pointed straight at them may read nothing unusual.

What corona UV inspection shows

A corona camera is tuned to the ultraviolet light that partial discharge emits. Instead of heat, it shows you where the air around a component is ionizing: a cracked insulator, a sharp edge or burr, contamination on a surface, a damaged conductor strand, a poor fit at high voltage.

This is the territory infrared tends to miss. Corona activity can be developing well before it produces measurable heat, and it concentrates on insulation and high-voltage hardware rather than on current-carrying joints. The output is different in nature too: rather than a temperature you read a discharge, visible as UV activity on a component.

Its blind spot mirrors thermography's. A warm, high-resistance bolted connection that is not discharging will not light up a UV camera.

Different physics, different findings

It helps to put the contrast plainly:

Different physics, different findings
Infrared thermographyCorona UV inspection
What it sensesHeatUltraviolet from partial discharge
Typical findingsLoose or corroded connections, overloads, imbalanceInsulation defects, contamination, sharp points at high voltage
Strong onCurrent-carrying, loaded componentsHigh-voltage insulation and hardware
Weak onFaults that discharge but do not heatFaults that heat but do not discharge
OutputA temperature you can measureA discharge you can see and locate

Neither column is the "better" method. They answer different questions, so the honest answer to "which one" is usually "both, for different parts of the job."

Why inspectors use both

Because the two methods cover each other's blind spots, a thorough program runs them together. Thermography catches the hot, loaded problems. Corona UV catches the quiet high-voltage ones. A finding that shows up on both is well evidenced; a finding on only one is a reason to look closer, not to dismiss it.

The common thread is evidence. Whichever camera you use, the value is in capturing what was seen in a form you can review, compare, and stand behind later.

How HealthyGrid fits in

HealthyGrid works with both kinds of material. Thermal analysis reads the measured data in radiometric files so you can examine temperatures and compare components. Corona review helps you go through UV video and look at the discharge points that were detected, each on its component.

A few things we are careful to say accurately. The tools assist the inspector; they surface measurements and detected activity as evidence. Detection coverage depends on inspection conditions and equipment limitations. Identifying a component in an image is not the same as diagnosing a fault. The interpretation, and the professional responsibility for it, stay with the inspector. What the software adds is speed and a consistent record, not a verdict.

FAQ

Does corona inspection replace infrared?
No. They detect different physics. Infrared finds heat-producing faults; corona UV finds partial discharge. Each misses what the other catches, so they are complementary.
Why does "corona" come up here?
In electrical inspection, corona means partial discharge in the air around high-voltage equipment, seen in ultraviolet. It is unrelated to the virus of the same name.
Can one platform handle both?
HealthyGrid supports both thermal analysis of radiometric files and review of corona UV video. In both cases the software assists the inspector and presents evidence; the inspector makes the call.

Try it: Review a thermal file in thermal analysis, or a UV video in corona review, free after a quick registration. Learn more at healthygrid.org.

All blog articles

Ask on WhatsApp